ASTM D5215

本頁面標準信息均來源于網絡收集，或由參與標準制定的供應商提供，只作為參考使用，為確保測試結果的準確性、節省您的時間，如需ASTM D5215標準詳細信息或ASTM D5215具體測試方法，請與我們技術人員聯系或給我們留言，我們將為您提供相關的技術支持。

ASTM D5215是烯基地板用膠黏劑著色的儀器評定的試驗法，本標準是于1993年被采用，并且于2012年重新復審的：

1.1ASTM D5215描述準確測量由于接觸膠粘劑而發生在乙烯基地板染色程度的過程和方法。乙烯基地板樣品接觸膠粘劑和未接觸到粘合劑之間顏色差異可以從CIELAB顏色刻度測得。

1.2本試驗方法提供了可能出現的乙烯基地板接觸膠粘劑染色過程中的視覺評價。

ASTM D5215英文簡介

Significance and se

Certain substances in adhesives may cause discoloration of vinyl flooring. This test method provides a means of measuring the discolorations that may occur in the vinyl as a result of contact with these adhesives. Vinyl flooring specimens, either contacting or not contacting the adhesive, are exposed to heat and VA light to accelerate discoloration. By means of colorimeter or spectrophotometer, color differences between exposed specimens are accurately measured. Therefore, instrumental evaluation rather than personal subjective evaluation is used to determine the amount of discoloration an adhesive may produce in vinyl flooring. This test method does not attempt to simulate or duplicate the heat and sunlight conditions that may impact vinyl floor coverings while in service.

1. Scope

1.1 This test method describes procedures and instrumentation for accurately measuring the degree of staining that may occur in vinyl flooring as a result of its contact with adhesives. Measured color differences between vinyl flooring specimens contacting the adhesive and not contacting the adhesive are expressed in the CIELAB Color-Scale System.

1.2 This test method provides for visual evaluation of staining which may occur when vinyl flooring contacts adhesives.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

ASTM Standards

D907 Terminology of Adhesives

D2244 Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates

E1347 Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry

E1349 Test Method for Reflectance Factor and Color by Spectrophotometry sing Bidirectional (45:0 or 0:45) Geometry

G53 Practice for Operating Light-and Water-Exposure Apparatus (Fluorescent V-Condensation Type) for Exposure of Nonmetallic Materials.